diff --git a/gift-box.scad b/gift-box.scad
index cb569df..b7eae33 100644
--- a/gift-box.scad
+++ b/gift-box.scad
@@ -3,16 +3,20 @@
 # Parameters
 
  */
-$box_inner_width = 10;
-$box_inner_depth = 20;
+$box_inner_width = 15;
+$box_inner_depth = 6;
 $box_inner_height = 15;
-$box_wall_thickness = 4;
+$box_wall_thickness = 6;
 // [0, 1] Higher the ratio, the bigger the bottom will be.
 $box_bottom_top_height_fraction = 0.2;
 // [0, 1] The amount the bottom and top will overlap.
 $overlap_fraction = 0.8;
 // [0, 1] The thickness of the overlap as a fraction of the wall thickness.
 $overlap_thickness_fraction = 0.5;
+// [1, *] Bottom scale. Scale the bottom up by settings this to a small amount like 1.05 to increase the gap between lid and bottom. Raise this number if the lid is too tight and won't go in, lower it if the lid is too loose.
+$bottom_scale = 1.05;
+// [0, 1] Screw scale. Lower this number if the screw is too tight and won't go through the hole.
+$lid_screw_scale = 0.94;
 
 /**
  
@@ -21,6 +25,8 @@ $overlap_thickness_fraction = 0.5;
 */
 include <Thread_Library.scad>;
 
+$fn = $preview ? 12 : 200;
+
 $box_outer_width = $box_inner_width + $box_wall_thickness * 2;
 $box_outer_depth = $box_inner_depth + $box_wall_thickness * 2;
 $box_outer_height = $box_inner_height + $box_wall_thickness * 2;
@@ -31,27 +37,47 @@ $top_height = $box_inner_height * (1 - $box_bottom_top_height_fraction);
 $overlap_height = $box_inner_height * $overlap_fraction;
 $overlap_thickness = $box_wall_thickness * $overlap_thickness_fraction;
 
+scale([$lid_screw_scale, $lid_screw_scale, $lid_screw_scale])
+translate([0, 0, 5])
+rotate([90, 0, 0])
+    screw();
 
-bottom();
-top();
+difference() {
+    scale([$bottom_scale, $bottom_scale, 1])
+        bottom();
+    thread();
+};
+
+translate([-10, 0, $bottom_height + $top_height + 2 * $box_wall_thickness])
+    rotate([0, 180, 0])
+    difference() {
+        color("blue")
+            translate([$box_outer_width, 0, $bottom_height + $top_height + 2 * $box_wall_thickness])
+            rotate([0, 180, 0])
+            top();
+       thread();
+    };
 
 module top() {
-    translate([-1 * $box_inner_width - $box_wall_thickness * 2 - 10, 0, 0])
-        difference() {
-            box_half($box_inner_width, $box_inner_depth, $top_height, $box_wall_thickness);
-            translate([-0.002, -0.002, 0])
-                scale([1.001, 1.001, 1.001])
-                translate([0, 0, $top_height + $bottom_height + $box_wall_thickness * 2])
-                color("red")
-                mirror([0, 0, 1])
-                bottom();
-        };
+    difference() {
+        box_half($box_inner_width, $box_inner_depth, $top_height, $box_wall_thickness);
+        translate([-0.002, -0.002, 0])
+            scale([1.001, 1.001, 1.001])
+            translate([0, 0, $top_height + $bottom_height + $box_wall_thickness * 2])
+            color("red")
+            mirror([0, 0, 1])
+            bottom();
+    };
 }    
 
 module bottom() {
     union() {
         box_half($box_inner_width, $box_inner_depth, $bottom_height, $box_wall_thickness);
-        box_half($box_inner_width + $box_wall_thickness, $box_inner_depth + $box_wall_thickness, $overlap_height + $box_wall_thickness, $overlap_thickness);
+        box_half(
+            $box_inner_width + $box_wall_thickness,
+            $box_inner_depth + $box_wall_thickness, $overlap_height + $box_wall_thickness,
+            $overlap_thickness
+        );
     };
 };
     
@@ -67,3 +93,23 @@ module box_half($width, $depth, $height, $wall_thickness) {
     };
 };
 
+$thread_z_offset = $bottom_height + $overlap_height / 2 + 7;
+
+$screw_scale = 0.33;
+module thread(length=$box_wall_thickness * (1/$screw_scale)) {
+    color("pink")
+        translate([$box_outer_width / 2, $box_wall_thickness + 0.1, $thread_z_offset])
+        rotate([90, 0, 0])
+        scale([$screw_scale, $screw_scale, $screw_scale])
+        trapezoidThread(length=length);
+}
+
+module screw() {
+    color("orange")
+        translate([$box_outer_width / 2, 0, $thread_z_offset])
+        rotate([90, 0, 0])
+        cylinder(h=5, d=15, $fn=6);
+    color("red")
+        translate([0, 0, 0])
+        thread(length=$box_wall_thickness * (1/$screw_scale));
+}
\ No newline at end of file
diff --git a/gift-box.stl b/gift-box.stl
index 15e92b5..aa7741b 100644
--- a/gift-box.stl
+++ b/gift-box.stl
@@ -1,3 +1,3 @@
 version https://git-lfs.github.com/spec/v1
-oid sha256:825e4e5e7265d0de33396ce76378dd6b1a691561aa4e9932cc803ec4cfb001fa
-size 4484
+oid sha256:b2bd9224085216132224f239e1a407b8dca045978d7c948fc356c8b4e849f96f
+size 44384