add thread library
This commit is contained in:
parent
a49c9ade86
commit
05bc10563d
GPG Key ID:
B2E280771CD62FCF
|
|
@ -0,0 +1,286 @@
|
|||
module threadPiece(Xa, Ya, Za, Xb, Yb, Zb, radiusa, radiusb, tipRatioa, tipRatiob, threadAngleTop, threadAngleBottom)
|
||||
{
|
||||
angleZ=atan2(Ya, Xa);
|
||||
twistZ=atan2(Yb, Xb)-atan2(Ya, Xa);
|
||||
|
||||
polyPoints=[
|
||||
[Xa+ radiusa*cos(+angleZ), Ya+ radiusa*sin(+angleZ), Za ],
|
||||
[Xa+ radiusa*cos(+angleZ), Ya+ radiusa*sin(+angleZ), Za + radiusa*tipRatioa ],
|
||||
[Xa , Ya , Za+ radiusa*(tipRatioa+sin(threadAngleTop)) ],
|
||||
[Xa , Ya , Za ],
|
||||
[Xa , Ya , Za+ radiusa*sin(threadAngleBottom) ],
|
||||
|
||||
[Xb+ radiusb*cos(angleZ+twistZ), Yb+ radiusb*sin(angleZ+twistZ), Zb ],
|
||||
[Xb+ radiusb*cos(angleZ+twistZ), Yb+ radiusb*sin(angleZ+twistZ), Zb+ radiusb*tipRatiob ],
|
||||
[Xb , Yb , Zb+ radiusb*(tipRatiob+sin(threadAngleTop)) ],
|
||||
[Xb , Yb , Zb ],
|
||||
[Xb , Yb , Zb+ radiusb*sin(threadAngleBottom)] ];
|
||||
|
||||
polyTriangles=[
|
||||
[ 0, 1, 6 ], [ 0, 6, 5 ], // tip of profile
|
||||
[ 1, 7, 6 ], [ 1, 2, 7 ], // upper side of profile
|
||||
[ 0, 5, 4 ], [ 4, 5, 9 ], // lower side of profile
|
||||
[ 4, 9, 3 ], [ 9, 8, 3 ], [ 3, 8, 2 ], [ 8, 7, 2 ], // back of profile
|
||||
[ 0, 4, 3 ], [ 0, 3, 2 ], [ 0, 2, 1 ], // a side of profile
|
||||
[ 5, 8, 9 ], [ 5, 7, 8 ], [ 5, 6, 7 ] // b side of profile
|
||||
];
|
||||
|
||||
polyhedron( polyPoints, polyTriangles );
|
||||
}
|
||||
|
||||
module shaftPiece(Xa, Ya, Za, Xb, Yb, Zb, radiusa, radiusb, tipRatioa, tipRatiob, threadAngleTop, threadAngleBottom)
|
||||
{
|
||||
angleZ=atan2(Ya, Xa);
|
||||
twistZ=atan2(Yb, Xb)-atan2(Ya, Xa);
|
||||
|
||||
threadAngleTop=15;
|
||||
threadAngleBottom=-15;
|
||||
|
||||
shaftRatio=0.5;
|
||||
|
||||
polyPoints1=[
|
||||
[Xa, Ya, Za + radiusa*sin(threadAngleBottom) ],
|
||||
[Xa, Ya, Za + radiusa*(tipRatioa+sin(threadAngleTop)) ],
|
||||
[Xa*shaftRatio, Ya*shaftRatio , Za + radiusa*(tipRatioa+sin(threadAngleTop)) ],
|
||||
[Xa*shaftRatio , Ya*shaftRatio , Za ],
|
||||
[Xa*shaftRatio , Ya*shaftRatio , Za + radiusa*sin(threadAngleBottom) ],
|
||||
|
||||
[Xb, Yb, Zb + radiusb*sin(threadAngleBottom) ],
|
||||
[Xb, Yb, Zb + radiusb*(tipRatiob+sin(threadAngleTop)) ],
|
||||
[Xb*shaftRatio , Yb*shaftRatio , Zb + radiusb*(tipRatiob+sin(threadAngleTop)) ],
|
||||
[Xb*shaftRatio , Yb*shaftRatio , Zb ],
|
||||
[Xb*shaftRatio , Yb*shaftRatio , Zb + radiusb*sin(threadAngleBottom) ] ];
|
||||
|
||||
polyTriangles1=[
|
||||
[ 0, 1, 6 ], [ 0, 6, 5 ], // tip of profile
|
||||
[ 1, 7, 6 ], [ 1, 2, 7 ], // upper side of profile
|
||||
[ 0, 5, 4 ], [ 4, 5, 9 ], // lower side of profile
|
||||
[ 3, 4, 9 ], [ 9, 8, 3 ], [ 2, 3, 8 ], [ 8, 7, 2 ], // back of profile
|
||||
[ 0, 4, 3 ], [ 0, 3, 2 ], [ 0, 2, 1 ], // a side of profile
|
||||
[ 5, 8, 9 ], [ 5, 7, 8 ], [ 5, 6, 7 ] // b side of profile
|
||||
];
|
||||
|
||||
|
||||
// this is the back of the raised part of the profile
|
||||
polyhedron( polyPoints1, polyTriangles1 );
|
||||
}
|
||||
|
||||
module trapezoidThread(
|
||||
length=45, // axial length of the threaded rod
|
||||
pitch=10, // axial distance from crest to crest
|
||||
pitchRadius=10, // radial distance from center to mid-profile
|
||||
threadHeightToPitch=0.5, // ratio between the height of the profile and the pitch
|
||||
// std value for Acme or metric lead screw is 0.5
|
||||
profileRatio=0.5, // ratio between the lengths of the raised part of the profile and the pitch
|
||||
// std value for Acme or metric lead screw is 0.5
|
||||
threadAngle=30, // angle between the two faces of the thread
|
||||
// std value for Acme is 29 or for metric lead screw is 30
|
||||
RH=true, // true/false the thread winds clockwise looking along shaft, i.e.follows the Right Hand Rule
|
||||
clearance=0.1, // radial clearance, normalized to thread height
|
||||
backlash=0.1, // axial clearance, normalized to pitch
|
||||
stepsPerTurn=24 // number of slices to create per turn
|
||||
)
|
||||
{
|
||||
|
||||
numberTurns=length/pitch;
|
||||
|
||||
steps=stepsPerTurn*numberTurns;
|
||||
|
||||
trapezoidRatio= 2*profileRatio*(1-backlash);
|
||||
|
||||
function threadAngleTop(i)= threadAngle/2;
|
||||
function threadAngleBottom(i)= -threadAngle/2;
|
||||
|
||||
function threadHeight(i)= pitch*threadHeightToPitch;
|
||||
|
||||
function pitchRadius(i)= pitchRadius;
|
||||
function minorRadius(i)= pitchRadius(i)-0.5*threadHeight(i);
|
||||
|
||||
function X(i)= minorRadius(i)*cos(i*360*numberTurns);
|
||||
function Y(i)= minorRadius(i)*sin(i*360*numberTurns);
|
||||
function Z(i)= pitch*numberTurns*i;
|
||||
|
||||
function tip(i)= trapezoidRatio*(1-0.5*sin(threadAngleTop(i))+0.5*sin(threadAngleBottom(i)));
|
||||
|
||||
// this is the threaded rod
|
||||
|
||||
if (RH==true)
|
||||
translate([0,0,-threadHeight(0)*sin(threadAngleBottom(0))])
|
||||
for (i=[0:steps-1])
|
||||
{
|
||||
threadPiece(
|
||||
Xa= X(i/steps),
|
||||
Ya= Y(i/steps),
|
||||
Za= Z(i/steps),
|
||||
Xb= X((i+1)/steps),
|
||||
Yb= Y((i+1)/steps),
|
||||
Zb= Z((i+1)/steps),
|
||||
radiusa= threadHeight(i/steps),
|
||||
radiusb= threadHeight((i+1)/steps),
|
||||
tipRatioa= tip(i/steps),
|
||||
tipRatiob= tip((i+1)/steps),
|
||||
threadAngleTop= threadAngleTop(i),
|
||||
threadAngleBottom= threadAngleBottom(i)
|
||||
);
|
||||
|
||||
shaftPiece(
|
||||
Xa= X(i/steps),
|
||||
Ya= Y(i/steps),
|
||||
Za= Z(i/steps),
|
||||
Xb= X((i+1)/steps),
|
||||
Yb= Y((i+1)/steps),
|
||||
Zb= Z((i+1)/steps),
|
||||
radiusa= threadHeight(i/steps),
|
||||
radiusb= threadHeight((i+1)/steps),
|
||||
tipRatioa= tip(i/steps),
|
||||
tipRatiob= tip((i+1)/steps),
|
||||
threadAngleTop= threadAngleTop(i),
|
||||
threadAngleBottom= threadAngleBottom(i)
|
||||
);
|
||||
}
|
||||
|
||||
if (RH==false)
|
||||
translate([0,0,-threadHeight(0)*sin(threadAngleBottom(0))])
|
||||
mirror([0,1,0])
|
||||
for (i=[0:steps-1])
|
||||
{
|
||||
threadPiece(
|
||||
Xa= X(i/steps),
|
||||
Ya= Y(i/steps),
|
||||
Za= Z(i/steps),
|
||||
Xb= X((i+1)/steps),
|
||||
Yb= Y((i+1)/steps),
|
||||
Zb= Z((i+1)/steps),
|
||||
radiusa= threadHeight(i/steps),
|
||||
radiusb= threadHeight((i+1)/steps),
|
||||
tipRatioa= tip(i/steps),
|
||||
tipRatiob= tip((i+1)/steps),
|
||||
threadAngleTop= threadAngleTop(i),
|
||||
threadAngleBottom= threadAngleBottom(i)
|
||||
);
|
||||
|
||||
shaftPiece(
|
||||
Xa= X(i/steps),
|
||||
Ya= Y(i/steps),
|
||||
Za= Z(i/steps),
|
||||
Xb= X((i+1)/steps),
|
||||
Yb= Y((i+1)/steps),
|
||||
Zb= Z((i+1)/steps),
|
||||
radiusa= threadHeight(i/steps),
|
||||
radiusb= threadHeight((i+1)/steps),
|
||||
tipRatioa= tip(i/steps),
|
||||
tipRatiob= tip((i+1)/steps),
|
||||
threadAngleTop= threadAngleTop(i),
|
||||
threadAngleBottom= threadAngleBottom(i)
|
||||
);
|
||||
}
|
||||
|
||||
rotate([0,0,180/stepsPerTurn])
|
||||
cylinder(
|
||||
h=length+threadHeight(1)*(tip(1)+sin( threadAngleTop(1) )-1*sin( threadAngleBottom(1) ) ),
|
||||
r1=minorRadius(0)-clearance*threadHeight(0),
|
||||
r2=minorRadius(0)-clearance*threadHeight(0),
|
||||
$fn=stepsPerTurn
|
||||
);
|
||||
}
|
||||
|
||||
module trapezoidThreadNegativeSpace(
|
||||
length=45, // axial length of the threaded rod
|
||||
pitch=10, // axial distance from crest to crest
|
||||
pitchRadius=10, // radial distance from center to mid-profile
|
||||
threadHeightToPitch=0.5, // ratio between the height of the profile and the pitch
|
||||
// std value for Acme or metric lead screw is 0.5
|
||||
profileRatio=0.5, // ratio between the lengths of the raised part of the profile and the pitch
|
||||
// std value for Acme or metric lead screw is 0.5
|
||||
threadAngle=30, // angle between the two faces of the thread
|
||||
// std value for Acme is 29 or for metric lead screw is 30
|
||||
RH=true, // true/false the thread winds clockwise looking along shaft, i.e.follows the Right Hand Rule
|
||||
countersunk=0, // depth of 45 degree chamfered entries, normalized to pitch
|
||||
clearance=0.1, // radial clearance, normalized to thread height
|
||||
backlash=0.1, // axial clearance, normalized to pitch
|
||||
stepsPerTurn=24 // number of slices to create per turn
|
||||
)
|
||||
{
|
||||
|
||||
translate([0,0,-countersunk*pitch])
|
||||
cylinder(
|
||||
h=2*countersunk*pitch,
|
||||
r2=pitchRadius+clearance*pitch+0.25*pitch,
|
||||
r1=pitchRadius+clearance*pitch+0.25*pitch+2*countersunk*pitch,
|
||||
$fn=24
|
||||
);
|
||||
|
||||
translate([0,0,countersunk*pitch])
|
||||
translate([0,0,-pitch])
|
||||
trapezoidThread(
|
||||
length=length+0.5*pitch, // axial length of the threaded rod
|
||||
pitch=pitch, // axial distance from crest to crest
|
||||
pitchRadius=pitchRadius+clearance*pitch, // radial distance from center to mid-profile
|
||||
threadHeightToPitch=threadHeightToPitch, // ratio between the height of the profile and the pitch
|
||||
// std value for Acme or metric lead screw is 0.5
|
||||
profileRatio=profileRatio, // ratio between the lengths of the raised part of the profile and the pitch
|
||||
// std value for Acme or metric lead screw is 0.5
|
||||
threadAngle=threadAngle, // angle between the two faces of the thread
|
||||
// std value for Acme is 29 or for metric lead screw is 30
|
||||
RH=true, // true/false the thread winds clockwise looking along shaft
|
||||
// i.e.follows Right Hand Rule
|
||||
clearance=0, // radial clearance, normalized to thread height
|
||||
backlash=-backlash, // axial clearance, normalized to pitch
|
||||
stepsPerTurn=stepsPerTurn // number of slices to create per turn
|
||||
);
|
||||
|
||||
translate([0,0,length-countersunk*pitch])
|
||||
cylinder(
|
||||
h=2*countersunk*pitch,
|
||||
r1=pitchRadius+clearance*pitch+0.25*pitch,
|
||||
r2=pitchRadius+clearance*pitch+0.25*pitch+2*countersunk*pitch,$fn=24,
|
||||
$fn=24
|
||||
);
|
||||
}
|
||||
|
||||
module trapezoidNut(
|
||||
length=45, // axial length of the threaded rod
|
||||
radius=25, // outer radius of the nut
|
||||
pitch=10, // axial distance from crest to crest
|
||||
pitchRadius=10, // radial distance from center to mid-profile
|
||||
threadHeightToPitch=0.5, // ratio between the height of the profile and the pitch
|
||||
// std value for Acme or metric lead screw is 0.5
|
||||
profileRatio=0.5, // ratio between the lengths of the raised part of the profile and the pitch
|
||||
// std value for Acme or metric lead screw is 0.5
|
||||
threadAngle=30, // angle between the two faces of the thread
|
||||
// std value for Acme is 29 or for metric lead screw is 30
|
||||
RH=true, // true/false the thread winds clockwise looking along shaft, i.e.follows the Right Hand Rule
|
||||
countersunk=0, // depth of 45 degree chamfered entries, normalized to pitch
|
||||
clearance=0.1, // radial clearance, normalized to thread height
|
||||
backlash=0.1, // axial clearance, normalized to pitch
|
||||
stepsPerTurn=24 // number of slices to create per turn
|
||||
)
|
||||
{
|
||||
difference()
|
||||
{
|
||||
cylinder(
|
||||
h=length,
|
||||
r1=radius,
|
||||
r2=radius,
|
||||
$fn=6
|
||||
);
|
||||
|
||||
trapezoidThreadNegativeSpace(
|
||||
length=length, // axial length of the threaded rod
|
||||
pitch=pitch, // axial distance from crest to crest
|
||||
pitchRadius=pitchRadius, // radial distance from center to mid-profile
|
||||
threadHeightToPitch=threadHeightToPitch, // ratio between the height of the profile and the pitch
|
||||
// std value for Acme or metric lead screw is 0.5
|
||||
profileRatio=profileRatio, // ratio between the lengths of the raised part of the profile and the pitch
|
||||
// std value for Acme or metric lead screw is 0.5
|
||||
threadAngle=threadAngle, // angle between the two faces of the thread
|
||||
// std value for Acme is 29 or for metric lead screw is 30
|
||||
RH=true, // true/false the thread winds clockwise looking along shaft
|
||||
// i.e.follows Right Hand Rule
|
||||
countersunk=countersunk, // depth of 45 degree countersunk entries, normalized to pitch
|
||||
clearance=clearance, // radial clearance, normalized to thread height
|
||||
backlash=backlash, // axial clearance, normalized to pitch
|
||||
stepsPerTurn=stepsPerTurn // number of slices to create per turn
|
||||
);
|
||||
}
|
||||
}
|
||||
BIN
display-camera-pi-mount-experiment.stl (Stored with Git LFS)
BIN
display-camera-pi-mount-experiment.stl (Stored with Git LFS)
Binary file not shown.
|
|
@ -8,9 +8,30 @@ $triangle_y_hole_gap = 20;
|
|||
$triangle_x_offset = 19;
|
||||
$triangle_y_offset = 5;
|
||||
|
||||
$fn=200;
|
||||
$fn=10;
|
||||
|
||||
screen_mount();
|
||||
use <Thread_Library.scad>
|
||||
|
||||
camera_mount();
|
||||
|
||||
$camera_mount_thickness = 1;
|
||||
$camera_screw_gap_y = 25.2;
|
||||
$camera_screw_diameter = 2.75;
|
||||
module camera_mount() {
|
||||
difference() {
|
||||
cylinder(h=$camera_mount_thickness, d=$camera_screw_gap_y);
|
||||
translate([0, 0, -0.1])
|
||||
cylinder(h=3 * $camera_mount_thickness, d=$camera_screw_gap_y - $camera_screw_diameter * 3);
|
||||
rotate([0, 0, 90])
|
||||
translate([$camera_screw_gap_y / 2 - $camera_screw_diameter / 1.33, 0, -0.1])
|
||||
cylinder(h=3 * $camera_mount_thickness, d=$camera_screw_diameter);
|
||||
rotate([0, 0, -90])
|
||||
translate([$camera_screw_gap_y / 2 - $camera_screw_diameter / 1.33, 0, -0.1])
|
||||
cylinder(h=3 * $camera_mount_thickness, d=$camera_screw_diameter);
|
||||
translate([-1 * $camera_screw_gap_y - $camera_screw_diameter / 1.33, -1 * $camera_screw_gap_y / 2, -0.1])
|
||||
cube([$camera_screw_gap_y, $camera_screw_gap_y, 3 * $camera_mount_thickness]);
|
||||
};
|
||||
}
|
||||
|
||||
module attachment_point() {
|
||||
difference() {
|
||||
|
|
|
|||
|
|
@ -0,0 +1,69 @@
|
|||
/**
|
||||
|
||||
# Parameters
|
||||
|
||||
*/
|
||||
$box_inner_width = 10;
|
||||
$box_inner_depth = 20;
|
||||
$box_inner_height = 15;
|
||||
$box_wall_thickness = 4;
|
||||
// [0, 1] Higher the ratio, the bigger the bottom will be.
|
||||
$box_bottom_top_height_fraction = 0.2;
|
||||
// [0, 1] The amount the bottom and top will overlap.
|
||||
$overlap_fraction = 0.8;
|
||||
// [0, 1] The thickness of the overlap as a fraction of the wall thickness.
|
||||
$overlap_thickness_fraction = 0.5;
|
||||
|
||||
/**
|
||||
|
||||
# Code
|
||||
|
||||
*/
|
||||
include <Thread_Library.scad>;
|
||||
|
||||
$box_outer_width = $box_inner_width + $box_wall_thickness * 2;
|
||||
$box_outer_depth = $box_inner_depth + $box_wall_thickness * 2;
|
||||
$box_outer_height = $box_inner_height + $box_wall_thickness * 2;
|
||||
|
||||
$bottom_height = $box_inner_height * $box_bottom_top_height_fraction;
|
||||
$top_height = $box_inner_height * (1 - $box_bottom_top_height_fraction);
|
||||
|
||||
$overlap_height = $box_inner_height * $overlap_fraction;
|
||||
$overlap_thickness = $box_wall_thickness * $overlap_thickness_fraction;
|
||||
|
||||
|
||||
bottom();
|
||||
top();
|
||||
|
||||
module top() {
|
||||
translate([-1 * $box_inner_width - $box_wall_thickness * 2 - 10, 0, 0])
|
||||
difference() {
|
||||
box_half($box_inner_width, $box_inner_depth, $top_height, $box_wall_thickness);
|
||||
translate([-0.002, -0.002, 0])
|
||||
scale([1.001, 1.001, 1.001])
|
||||
translate([0, 0, $top_height + $bottom_height + $box_wall_thickness * 2])
|
||||
color("red")
|
||||
mirror([0, 0, 1])
|
||||
bottom();
|
||||
};
|
||||
}
|
||||
|
||||
module bottom() {
|
||||
union() {
|
||||
box_half($box_inner_width, $box_inner_depth, $bottom_height, $box_wall_thickness);
|
||||
box_half($box_inner_width + $box_wall_thickness, $box_inner_depth + $box_wall_thickness, $overlap_height + $box_wall_thickness, $overlap_thickness);
|
||||
};
|
||||
};
|
||||
|
||||
module box_half($width, $depth, $height, $wall_thickness) {
|
||||
difference() {
|
||||
cube([
|
||||
$width + $wall_thickness * 2,
|
||||
$depth + $wall_thickness * 2,
|
||||
$height + $wall_thickness
|
||||
]);
|
||||
translate([$wall_thickness, $wall_thickness, $wall_thickness])
|
||||
cube([$width, $depth, $height + 0.1]);
|
||||
};
|
||||
};
|
||||
|
||||
Binary file not shown.
Loading…
Reference in New Issue